Tel+86 17621197907Serving 56+ countries
RICEWIND

ZTE / DC Power Systems (-48V)

ZXDU48 B600 (V5.0) Equipment information & support

The ZTE ZXDU48 B600 (V5.0) is a compact 2U embedded DC power subrack housing up to 2 x ZXD1500 (V5.0) rectifiers, delivering -48V 60A (3000W) for wireless micro-sites and DAS systems.

Equipment information

Brand
ZTE
Equipment model
ZXDU48 B600 (V5.0)
Equipment type
DC Power Systems (-48V)
Controller / software version
Confirm against the installed equipment
View full product specifications
ZTE ZXDU48 B600 (V5.0) Embedded DC Power System (-48V 60A 2U Subrack) - Official Front View

Information below comes from the current product catalogue. Confirm the controller, software version and configuration of the installed equipment separately.

AC Input Voltage
80V - 300V AC Wide Grid Tolerance
Supervisory Controller
CSU500 Compact Controller
Rated Distribution Capacity
60A / 3000W
Compatible Rectifiers
ZXD1500 (V5.0) Rectifier Modules
Nominal DC Output Voltage
-48VDC (-42V ~ -58V)
Chassis Form Factor
Floor-Standing High-Capacity DC Power System Cabinet

Alarms & troubleshooting

MAINS_FAIL / AC_POWER_LOSS
Power distribution Amber LED solid, controller buzzer active
Mains utility grid failure, upstream transformer trip, or main AC breaker open
1. Verify battery discharge current and remaining backup runtime on monitor;\n2. Start standby generator (DG) and confirm transfer switch closure;\n3. Measure incoming 3-phase AC voltage and frequency stability;\n4. After grid recovery, verify rectifiers soft-start and initiate boost charging.
LLVD_TRIP / LOAD_SHEDDING
Controller screen displays LLVD alarm, DC load contactor opened
Prolonged blackout caused battery voltage to drop below threshold (44.0VDC default), shedding non-critical loads
1. Confirm priority telecommunication loads on BLVD branch remain powered;\n2. Deploy mobile emergency power generators to replenish battery plant;\n3. Upon grid restoration, observe DC bus rising past reset threshold (48.0VDC);\n4. Verify all load shedding contactors re-engage and resume service.
SPD_FAIL / SURGE_ARRESTOR
Surge arrestor inspection window turns Red from Green, alarm relay closed
Lightning induced transient surge or utility overvoltage caused MOV thermal breakdown and disconnection
1. Inspect visual disconnect indicator window on AC surge protector module;\n2. Verify upstream SPD backup fuse or miniature circuit breaker status;\n3. Open SPD circuit breaker and pull out damaged plug-in cartridge;\n4. Insert genuine replacement cartridge (20kA/40kA rating) and reset breaker.

Access Complete Maintenance & Full Alarm Troubleshooting Manual

This page lists high-frequency critical alarm codes commonly encountered in field maintenance. Comprehensive manufacturer troubleshooting matrices, board-level repair guides, detailed electrical schematics, and firmware commissioning manuals are delivered alongside equipment upon formal project procurement, accompanied by dedicated FAE technical support.

Contact Account Manager for Full Manual

Share on-site information

  1. 01

    Identify the exact model

    Record the nameplate, system model and controller or module model.

  2. 02

    Keep the alarm details

    Record the full alarm text, indicator colour, timing and whether it persists.

  3. 03

    Describe recent changes

    Note recent replacements, software updates or configuration changes.

Record information visible in the existing interface. Electrical measurements, disassembly and replacement should follow the applicable manufacturer's manual and be performed by qualified personnel.

Your model and these details will be added to the enquiry form for you to review before sending.

Related technical articles

Browse the technical guides or send a question about this model.

View all articles

Need a replacement module or supporting equipment?

Confirm the full model, system configuration and compatibility requirements before enquiring about suitable products.

Ask about suitable products

Have a model and an on-site issue?

Share the exact model, alarm text and observed symptoms to help identify relevant information and compatibility requirements.

Request technical support