Tel+86 17621197907Serving 56+ countries
RICEWIND

Delta / DC Power Systems (-48V)

ESR4840AC Equipment information & support

The Delta ESR4840AC is an industrial-grade, high-frequency telecom rectifier module designed to convert standard AC utility power into a regulated nominal 54V DC (adjustable 43V~58V DC) output with a maximum current of 40A and a rated power of 2000W.

Equipment information

Brand
Delta
Equipment model
ESR4840AC
Equipment type
DC Power Systems (-48V)
Controller / software version
Confirm against the installed equipment
View full product specifications
Delta ESR4840AC Genuine Telecom Hardware Shot 1

Information below comes from the current product catalogue. Confirm the controller, software version and configuration of the installed equipment separately.

AC Input Voltage
80V AC ~ 300V AC
Rated Output Voltage
-48VDC (-42V ~ -58V)
Maximum Output Current
40A
Rated Output Power
2000W
Maximum Efficiency
≥ 95.0%
Operating Temperature Range
-40°C ~ +75°C

Alarms & troubleshooting

MAINS_FAIL / AC_POWER_LOSS (Utility Grid Failure / Total AC Ingress Loss)
Cabinet controller red ALARM LED solid with acoustic buzzer; system seamlessly transitions to battery discharge.
Grid utility failure, upstream transformer trip, automatic transfer switch (ATS) fault, or tripped main breaker.
1. Verify battery discharge current and remaining backup runtime on controller; 2. Start backup diesel generator (DG) and verify ATS transfer; 3. Measure incoming 3-phase line voltage and frequency stability; 4. Upon grid restoration, verify rectifiers soft-start and engage battery recharge.
LLVD_TRIP / LOAD_SHEDDING (Load Low Voltage Disconnect Tripped)
Controller LCD triggers LLVD alarm; LLVD contactor mechanically opens; secondary load branches de-energized.
Prolonged mains outage discharging batteries to protection threshold (typically 44.0VDC). System automatically sheds secondary loads to preserve core communications.
1. Confirm critical core branches (BLVD circuit) remain energized and protected; 2. Dispatch emergency mobile power generation cart to site; 3. Upon grid recovery, monitor DC bus voltage ramp above re-engagement threshold (48.0VDC); 4. Verify LLVD contactor re-closes and secondary equipment boots normally.
SPD_FAIL / SURGE_ARRESTOR (Surge Protective Device Degradation / Tripped)
Controller registers SPD alarm; SPD module inspection window turns from Green to Red; alarm dry contact closes.
Site subjected to lightning surge strike or sustained overvoltage, causing MOV thermal breakdown and disconnect.
1. Inspect SPD indicator flags (red flag confirms blown cartridge); 2. Check SPD dedicated backup fuse or circuit breaker; 3. Open SPD isolation switch, extract damaged plug-in cartridge; 4. Replace with genuine replacement cartridge matching rating (20kA/40kA); 5. Close circuit, verify green status flag and alarm self-clearing.

Access Complete Maintenance & Full Alarm Troubleshooting Manual

This page lists high-frequency critical alarm codes commonly encountered in field maintenance. Comprehensive manufacturer troubleshooting matrices, board-level repair guides, detailed electrical schematics, and firmware commissioning manuals are delivered alongside equipment upon formal project procurement, accompanied by dedicated FAE technical support.

Contact Account Manager for Full Manual

Share on-site information

  1. 01

    Identify the exact model

    Record the nameplate, system model and controller or module model.

  2. 02

    Keep the alarm details

    Record the full alarm text, indicator colour, timing and whether it persists.

  3. 03

    Describe recent changes

    Note recent replacements, software updates or configuration changes.

Record information visible in the existing interface. Electrical measurements, disassembly and replacement should follow the applicable manufacturer's manual and be performed by qualified personnel.

Your model and these details will be added to the enquiry form for you to review before sending.

Related technical articles

Browse the technical guides or send a question about this model.

View all articles

Need a replacement module or supporting equipment?

Confirm the full model, system configuration and compatibility requirements before enquiring about suitable products.

Ask about suitable products

Have a model and an on-site issue?

Share the exact model, alarm text and observed symptoms to help identify relevant information and compatibility requirements.

Request technical support